Gleamworks

Bricklin Paint Protection Film

PAINT PROTECTION FILM FOR VANCOUVER RICHMOND BURNABY SURREY LOWER MAINLAND, BC

WHAT IS PAINT PROTECTION FILM (CLEAR BRA) ?

Paint Protection Film for Bricklin means a clear layer we shape around the areas that take grit, wash marks, and road spray. It does not repair failed gel coat or hide a bad prior repair. Vancouver receives 1,119.2 mm of rain in a year, so dirt and water sit on cars that stay outside. The film takes that wear first and can be removed later, subject to the panel condition underneath. If you are comparing Bricklin PPF cost, our Gold Package starts at $1,799 and includes full hood, full fenders, mirrors, front bumper, and headlights. We map coverage around the condition of your actual panels rather than sell a fixed pattern by phone. That inspection tells you whether a front-end package or separate pieces make sense.
System x accredited installation center
Gtechniq Logo
carpro approved detailing centre
revivify coatings logo

BENEFITS OF PAINT PROTECTION FILM

At $1,299, our published Light Package starts near the cost of repainting one panel at a Metro Vancouver body shop, typically $600–$1,500. That package covers half hood, half fenders, mirrors, and front bumper; old panels need an inspection before we promise coverage. Bricklin Paint Protection Film is most useful where front-end chips would force a repair on a car whose original acrylic gel-coat panels deserve care. Repainting also leaves you managing a repair on a discontinued classic. Water gets into a chip during Vancouver’s freeze-thaw winter and expands. On a Bricklin, we inspect chips, seams, and panel condition before we cut XPEL, STEK DYNOshield, or SunTek to fit. The starting price gives you a useful first comparison; panel condition decides the scope.

1

+

Happy Clients

1

%

Customer Satisfaction

PRICING FOR Bricklin

In the car graphics below, the areas in red indicate coverage area, not colour. Paint protection film comes is transparent and can have either a gloss or matte finish.

 
paint- protection film standard package

PPF LIGHT PACKAGE

  • Covers half hood
  • Covers half fenders
  • Covers mirrors
  • Front bumper

From $1299

GET A QUOTE
paint protection film ultimate package

PPF GOLD PACKAGE

  • Covers full hood
  • Covers full fenders
  • Covers mirrors
  • Front bumper
  • Headlight

From $1799

GET A QUOTE
paint protection film platinum package

PPF PLATINUM PACKAGE

  • Covers full vehicle.

From $4699

GET A QUOTE

ADDITIONAL OPTIONS

BAGGAGE REST

paint protection film rocker cover

ROCKER COVERS

DOOR SILLS (PAIR)

FAQ

Book Your Ceramic Coating Today – Protect Your Investment for the Next Years.

How long does it take to apply paint protection film?

The work does not have a useful one-size-fits-all time for an SV-1. We first inspect the acrylic gel-coat panels, note chips and old repairs, and decide which edges need coverage. At YVR, December’s mean daily low is 1.2°C. That near-freezing weather can enlarge an old chip once water gets in, so we record those areas before fitting the film. We then prepare the panel, test the coverage layout, and install each piece around its actual shape. A car with sound panels and a clear coverage plan moves ahead more smoothly than one with unknown repairs. Bring the car in for an inspection before setting the scope.

Are there any special care instructions for paint protection film?

If you are searching Bricklin Paint Protection Film Vancouver service, start with a wash routine that removes grit before you touch the surface. Vancouver has 169.5 days each year with measurable precipitation, so road dirt often dries onto cars between washes. Rinse loose grit first, use mild car-wash soap, and dry with clean towels rather than rubbing dirt across the panel. Check edges after washing, especially around the front bumper and lower panels. Remove cedar and fir sap, pollen, bird mess, and cottonwood fluff before they sit in the sun. Shaded parking can also bring moss or algae onto exterior surfaces. An SV-1’s acrylic gel-coat panels need the same care before and after film goes on. Leaving grit in place turns routine washing into needless rubbing.

What happens if the film gets scratched?

A mark needs an inspection before anyone decides it is only in the film. We look at the damaged area, clean it, and check whether the mark reached the panel below. Winter traffic throws brine and grit into lower body areas, where scratches and chips often need closer attention. If damage stays in the protective layer, we can discuss replacing that section rather than repainting an original Bricklin panel. Manufacturer film warranty can run up to 9 years, but the terms and the cause of damage matter, so we check the product record before promising an outcome. Gleamworks has protected more than 2,000 vehicles over nine years. Replacing a damaged section may keep you from adding a repaint to a discontinued car’s history.

Can paint protection film be removed?

Yes, we can remove film, but we treat an older Bricklin as an inspection job rather than a routine peel. We check the edges, the condition of the acrylic gel-coat panel, and any prior repair before we start. Coastal salt air and wet road spray make it worth cleaning the lower sections before removal, so we can see what sits at the seams. Keep the product and service records if you have them. When STEK Final Coat was added, a 12-year extended warranty may be available, and the record helps us confirm what was installed. Panel condition, film condition, and the reason for removal decide the right approach.

What kind of vehicles can use PPF?

Film can suit a discontinued classic when the owner wants to limit fresh front-end wear without hiding the car’s condition. The Bricklin SV-1 was built in New Brunswick from 1974 to 1976, with roughly 2,850 cars made and acrylic gel-coat body panels. That makes a close panel inspection more useful than a generic pattern or a quick online quote. We assess original surfaces, repaired areas, seams, and the places that face road grit. Ferry trips add salt spray on the deck, while wet winter chips can grow as water freezes and expands. The best coverage plan depends on which panels remain sound and which ones already need repair.

What areas of Vancouver do you serve?

We provide paint protection film to Vancouver, Richmond and Lower Mainland clients.

Gleamworks Detailing & Ceramic Coating
By appointment only.
5-8855 Laurel Street,
Vancouver, BC, Canada V6P 3V9.
View a map and directions.

How much does Bricklin PPF cost?

From $1,299, a Light Package covers the half hood, half fenders, mirrors, and front bumper. Gold coverage starts at $1,799, while full-vehicle Platinum coverage starts at $4,699. An SV-1 needs a panel-by-panel inspection first. Acrylic gel-coat condition, past repairs, and edge work decide the final scope and price.

Should I use a generic installer?

No, not by default. A generic installer may quote less, but the lower price can leave out paint correction, a close check of old panel repairs, careful edge work, or clear warranty terms. Gleamworks installs XPEL, STEK DYNOshield, and SunTek film. For an aged acrylic gel-coat body, the price difference should buy proper prep and a fit checked for each panel.

What are Bricklin PPF drawbacks?

The real drawbacks are cost, preparation time, and the fact that film can still be damaged. A hard impact can tear or puncture it, and a damaged section may need replacement. Film also will not hide failing gel-coat, deep cracks, or poor past repairs. A cheap install with dirt, poor seams, or lifted edges can look worse than leaving the panel bare.

How long does Bricklin PPF last?

It can carry up to a 9-year manufacturer warranty, depending on the film and coverage. STEK Final Coat can add an available 12-year extended warranty. On a Bricklin, sun exposure, neglected washing, strong chemicals, and unstable old repairs can shorten its useful life. We inspect the gel-coat before installation and confirm the product warranty for the chosen film.

What ruins paint protection film?

Avoid abrasive polishing, strong solvents, and pressure-washer blasts held close to an edge. Do not pick at a lifted corner or scrape ice across the film. Wash away bird droppings, tree sap, salt, and road grime rather than letting them sit. These habits can stain the surface, wear the top layer, and let water work into vulnerable edges.

Can I wash Bricklin PPF safely?

Yes, hand washing is the safest routine for a protected Bricklin. Touchless wash bays are generally fine if they use sensible chemicals, but brush tunnels can mar film and catch edges. Keep a pressure washer moving and avoid aiming directly at seams. Use clean wash mitts and microfiber drying towels, since dirty tools create the light marring film is meant to reduce.

Is Bricklin PPF worth it in Vancouver?

Yes, Vancouver gives front-end film a strong case. The city receives 1,159.5 mm of annual precipitation over 169.5 days with measurable precipitation. Water can sit in chips, then dry into mineral spots or work into damaged areas during freeze-thaw weather. Sea-to-Sky Highway trips add gravel strikes and road grit, especially on the bumper, hood, and forward fenders.

Does PPF protect Bricklin collector value?

Yes, preserving original panels matters more than chasing a resale percentage. Roughly 2,850 Bricklins were built, so keeping sound original gel-coat can help avoid reconditioning later. Repainting one bumper, hood, or fender in Metro Vancouver is typically in the range of $600–$1,500. Film can reduce chip damage, but it cannot restore failing gel-coat or conceal prior repairs.

REQUEST AN APPOINTMENT ONLINE

After you submit the form, a representative will call you back with the information you’ll need to make an appointment.





    Please prove you are human by selecting the flag.

    ▲
    Cart
    Call Now